Hi Everyone. Well, after 15 years the RV-Dreams Community Forum is coming to an end. Since it began in August 2005, we've had 58 Million page views, 124,000 posts, and we've spent about $15,000 to keep this valuable resource for RVers free and open. But since we are now off the road and have settled down for the next chapter of our lives, we are taking the Forum down effective June 30, 2021. It has been a tough decision, but it is now time.


We want to thank all of our members for their participation and input over the years, and we want to especially thank those that have acted as Moderators for us during our amazing journey living and traveling in our RV and growing the RV-Dreams Family. We will be forever proud to have been founders of this Forum and to have been supported by such a wonderful community. Thank you all!!

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: How to Ground Tri-pod mount Satellite Dish?


RV-Dreams Family Member

Status: Offline
Posts: 149
Date:
How to Ground Tri-pod mount Satellite Dish?


We have our Dishnetwork satellite dish mounted on a tri-pod and I am wondering if anyone has ever "grounded" their dish or how you have gone about prevention for lightning strikes?

Anyone have any experience with Lightning arrestors for grounding the RG6 cables?

Our neighbor recently had a lightning strike on their dish here in the campground and it took out thier TV and receiver.

Any suggestions are appreciated.



__________________

Ken & Mary and 2 Spoiled Furbaby Shih-Tzu's
2005 Ford F-250 SD Turbo Diesel
2004 Sunnybrook Titan 31BWFS

"Fulltiming since May of 2012" (newbies!)

"...and we rolled clean out of sight!" -Bob Seger



RV-Dreams Family Member

Status: Offline
Posts: 5399
Date:

In our case, we are "static" full-timers in that we seldom move from our current spot.  (At least until we retire and start to travel.)  When we put up our tripod mount, I bought three of those screw devices that one uses to hook a dog's leash to so that they can move around a yard.  I then use those to anchor in three directions on the tripod.

Now, they may not really serve well as a ground for a dish and tripod because they don't go into the ground as much as most electrical grounds do.  (At least for permanent homes that is.  Most of those ground rods are at least 5 feet long.)  But, in our case, I put those in place to anchor the tripod, not serve as a ground.

Years ago, I remember that Radio Shack used to have devices to ground one's cable, but again, those were designed for "permanent" locations, if I remember correctly.

Hopefully, someone will come along with the right solution for such a problem, and when they do, I will learn something new as well.

Terry



__________________

Terry and Jo

2010 Mobile Suites 38TKSB3
2008 Ford F450
2019 Ford Expedition Max as Tag-along or Scout

Our photos on Smugmug



RV-Dreams Family Member

Status: Offline
Posts: 2074
Date:

If you want to do this, mostly for peace of mind if you are concerned, here is an inexpensive device:

 

http://www.solidsignal.com/pview.asp?mc=09&p=212FF75F225-21&d=TII-InLine-Coaxial-Lightning-Surge-Protector-Female-to-Female-Connector-(212FF75F22521)&c=Surge Protection&sku=811286010078

 

You will have to cut and past the link unless Terry can activate it.  The device costs $16

 

Put a wire from the lug on the device side to the chassis ground of the trailer.  This needs to go physically “at” the trailer.  Hold down stakes at the dish are of no help as pertains to lighting.

 

Grounding, as suggested, is not a for sure thing in any way shape or form. It’s better than nothing that’s for sure, but not guaranteed and that is a long discussion.

 

May I better recommend a $5 / month insurance plan such as the one Direct TV offers.  I don’t know if Dish has the same plan or not.  It covers everything and IMO is pretty inexpensive insurance for you satellite equipment.

 

Hope this helps and fee free to PM me if you need to.

 

Bill

 

Edit by moderator: Activated link.  Terry



-- Edited by Terry and Jo on Monday 25th of June 2012 06:06:54 PM

__________________

Bill & Linda



RV-Dreams Family Member

Status: Offline
Posts: 5399
Date:

Reply to Bill's comment:

I tried to activate his link, but for some reason when I test after activating, I get a "server not available" error message.  When I use the "copy and paste" method, it works to get one to the internet page needed.

I'll try again this evening when I get home.

EDIT:  Got home and attempted link activation again.  It is now working.

Terry



-- Edited by Terry and Jo on Monday 25th of June 2012 06:08:03 PM

__________________

Terry and Jo

2010 Mobile Suites 38TKSB3
2008 Ford F450
2019 Ford Expedition Max as Tag-along or Scout

Our photos on Smugmug



RV-Dreams Family Member

Status: Offline
Posts: 2074
Date:

Terry and Jo wrote:

Reply to Bill's comment:

I tried to activate his link, but for some reason when I test after activating, I get a "server not available" error message.  When I use the "copy and paste" method, it works to get one to the internet page needed.

Terry


MaryBee:  The provider is www.solidsignal.com.  This link will activate from the forum page.  Go there, then at the top of the Solid Signal home page in the search box, using cut and paste, put:  212FF75F225-21  which is the part number.  That worked when I tried it.

 

Bill



__________________

Bill & Linda



RV-Dreams Family Member

Status: Offline
Posts: 149
Date:

Thanks, I will check things out.

 



__________________

Ken & Mary and 2 Spoiled Furbaby Shih-Tzu's
2005 Ford F-250 SD Turbo Diesel
2004 Sunnybrook Titan 31BWFS

"Fulltiming since May of 2012" (newbies!)

"...and we rolled clean out of sight!" -Bob Seger

Page 1 of 1  sorted by
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us