Hi Everyone. Well, after 15 years the RV-Dreams Community Forum is coming to an end. Since it began in August 2005, we've had 58 Million page views, 124,000 posts, and we've spent about $15,000 to keep this valuable resource for RVers free and open. But since we are now off the road and have settled down for the next chapter of our lives, we are taking the Forum down effective June 30, 2021. It has been a tough decision, but it is now time.


We want to thank all of our members for their participation and input over the years, and we want to especially thank those that have acted as Moderators for us during our amazing journey living and traveling in our RV and growing the RV-Dreams Family. We will be forever proud to have been founders of this Forum and to have been supported by such a wonderful community. Thank you all!!

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Lippert Jacks won't work


RV-Dreams Family Member

Status: Offline
Posts: 420
Date:
Lippert Jacks won't work


Hello All,

We have the Lippert auto system and it has stopped working as we were bringing the legs up to leave our campsite.  The back and middle legs went up but the front are still down.  The trailer is on the truck so we can't move our truck and we are blocking the campsite road.  ARG! 

The relay to the pump clicks, but the pump won't come on.  We are still hooked up to power and nothing helps.

Ideas?

 



__________________

Debbie & Steve McCormack...and Hurley too!

Our Blog: Down the Road

2013 Montana 3582RL

2013 Dodge 3500HD Laramie Longhorn Dually

Fulltime since June 2014



RV-Dreams Family Member

Status: Offline
Posts: 1122
Date:

The relay click you are hearing should be a contactor sending power to the pump motor. That's a good sign in that all the electrical controls are working correctly up to the contactor.  If the pump isn't turning (you would hear the noise) then the motor is most likely shot. Could be a loose connection, blown fuse, tripped overload or something else, but failed electric motors aren't unusual. Wait a while and see if a thermal overload might have tripped and will reset itself. Failing that, and assuming you know how to use a multimeter ... ensure the ground wire (of the pump motor) is properly connected (it is usually a black heavy wire) and there is continuity with ground, then with the multimeter black lead on ground, put the red lead on the positive side of the pump motor (usually a red colored heavy wire). Have someone activate the "retract" function to try to raise the front landing gear. If the click of the contractor causes the multimeter to go from "0" volts on the motor positive terminal, to go to "12V DC", but the motor does not turn the electrical connection to the pump motor is probably sound ... and the motor has failed internally. The pump can be run manually using a drill motor (most people have a cordless drill). Not sure of the size of the socket pocket on the motor, but running the cordless drill one way will turn the pump in a direction that will extend the gear and reversing the drill motor will cause the pump to run the other way and retract the gear. This should allow you to get everything sucked up and able to travel ... go directly to a shop for repairs. If none of this makes sense, then call a mobile RV Technician.

Sorry to hear of your troubles ... these things ALWAYS happen at inopportune times. Best of luck to you on this.

Ron



-- Edited by RonC on Thursday 8th of June 2017 03:56:02 PM



-- Edited by RonC on Thursday 8th of June 2017 05:52:53 PM

__________________

Ron and Janice

 

2016 Ford F350, King Ranch, DRW, 4x4, CC, 6.7 PS Diesel, remote control air lift system

2017 Durango Gold 381REF, Lambright furniture, MCD shades, morRYDE IS, 8K Disc brakes, GY G114  LR H Tires, 27,320 lbs CGVW

FT class of 2016



RV-Dreams Family Member

Status: Offline
Posts: 1756
Date:

So sorry, HATE anything Lippert, don't get me started. We have to raise, lower landing gear multiple times to get it to stay in place before heading down the road.

Check the hoses, if any are squishy they need to be replaced, with all slides in check hydraulic fluid level, then hope you finda good repair shop.

We feel your pain, 3 trips to the shop for Lippert hydraulic issues in Mar 2016 left us fuming and frustrated.

__________________

FT - July 2013

 

2010 38TKSB3 DRV Mobile Suites

2012 Ford F450

 

Dale and Ruth Travelling with Tazzy Kat!

 

IMAG0142_zps070d30d8.jpg

 

 

 

 



RV-Dreams Family Member

Status: Offline
Posts: 1122
Date:

NWescapee ... are you still having trouble with your Lippert Level Up system? I was under the impression that your "drifting" jacks problem had been resolved.

__________________

Ron and Janice

 

2016 Ford F350, King Ranch, DRW, 4x4, CC, 6.7 PS Diesel, remote control air lift system

2017 Durango Gold 381REF, Lambright furniture, MCD shades, morRYDE IS, 8K Disc brakes, GY G114  LR H Tires, 27,320 lbs CGVW

FT class of 2016



RV-Dreams Family Member

Status: Offline
Posts: 2074
Date:

DebbieM wrote:

Hello All,

We have the Lippert auto system and it has stopped working as we were bringing the legs up to leave our campsite.  The back and middle legs went up but the front are still down.  The trailer is on the truck so we can't move our truck and we are blocking the campsite road.  ARG! 

The relay to the pump clicks, but the pump won't come on.  We are still hooked up to power and nothing helps.

Ideas?

 


 Let's assume the pump motor ran to raise the rear and center jacks.  That's what you state in the first two sentences.  In the manual there are instructions, as Ron indicated, to run the pump with a drill motor with a chuck into the motor drive shaft.  (However, it might take a right angle drive depending on clearance.  Yes, I carry one of those - really handy when needed.)  But the "click" you maybe hearing is the hydraulic control relay for the front jacks, not the motor control relay.  So . . . assuming all of the above is the case you would need to use a drill motor to run the pump and also at the same time have someone press the "up" button for the jacks.  That might well do it.

By this time you probably have the jacks up and this is solved.  But though I would give it a shot a suggesting a course of action.  

We don't have the Lippert leveling system (have the Quadra "Big Foot") but do have the Lippert pump motor / hydraulic system for the slides and they work the same way as far as pump operation is concerned.

(Edited to correct comment about limit switch.  Thanks, Ron.)



-- Edited by Bill and Linda on Saturday 10th of June 2017 12:36:23 PM

__________________

Bill & Linda



RV-Dreams Family Member

Status: Offline
Posts: 1756
Date:

Yep, still problematic.  The one thing that seems to work most of the time, knock on wood, is to raise and lower the landing gear multiple times after all the slides are in and the side to side levelers are up.  We've had  a couple of times where they started drifting again, so we raise / lower / raise / lower, etc, and then they seem to stay.

I say knock on wood because we have several driving days ahead of us in the next 4 weeks.



__________________

FT - July 2013

 

2010 38TKSB3 DRV Mobile Suites

2012 Ford F450

 

Dale and Ruth Travelling with Tazzy Kat!

 

IMAG0142_zps070d30d8.jpg

 

 

 

 



RV-Dreams Family Member

Status: Offline
Posts: 50
Date:

I'm sorry to hear you are having problems. I know you probably have your issue fixed. I would probably have just manually jogged the leveling system jacks down just for an instant, to see if the pump would work with a switch different then the front landing gear switch button. If the pump comes on to lower the levelers then obviously it is not the pump. I might also unhitched and tried raising the landing gear just a tad. I also think there is a oil cutoff switch too. 

Bill you bring up some good points! I didn't know they had limit switches on these cylinders. I want to go out and try mine now. I think in manual the front landing gear just runs the pump until you take your finger off the button. 

I was just wondering, did you have to raise the front landing before hitching the trailer and then after hitching up the front landing gear would not go up the rest of the way?



-- Edited by Bruce and Robin on Friday 9th of June 2017 07:46:19 PM

__________________

Bruce & Robin

2013 GMC Sierra 3500HD SLT DRW 4x4 CC

2014 DRV Mobile Suites 38TKSB3 

Full Timers - March 2017

Our Blog at https://rv-revelations.blog/



RV-Dreams Family Member

Status: Offline
Posts: 2074
Date:

Bruce and Robin wrote:

Bill you bring up some good points! I didn't know they had limit switches on these cylinders. I want to go out and try mine now. I think in manual the front landing gear just runs the pump until you take your finger off the button. 

 

-- Edited by Bruce and Robin on Friday 9th of June 2017 07:46:19 PM


 Bruce, my bad.  Lippert does not use a simplistic "limit" switch.  Much more complicated system and Ron corrected me on that point.  Doing trouble shooting at a distance can lead to errors but I was giving it a shot.  It's probably working by now anyway.

The Quadra system has 4 independent jacks.  Independent to the extent there are four individual hydraulic pumps at the each jack and two simple relay controls also at the jack.  One relay is for up and the other reverses the 12 volt polarity to the pump for down.  So if one has a failure of the control system a clip lead with #14 wire will make the jack run up or down as required.  They have a up limit switch and if that goes bad it will keep the jacks from running.  But a clip lead will also bypass that in a pinch as well.  Its not they can't fail, its just there are ways around a failure in some cases and I was hoping the same for the OP as a long shot.



__________________

Bill & Linda



RV-Dreams Family Member

Status: Offline
Posts: 50
Date:

Thanks Bill! Sounds like you have a system you can work around if you have any issues. I am not a fan of Lippert in my short time of troubleshooting and looking at their system design. Actually they could have a good system if they used better quality o-rings and seals. I don't understand cost cutting measures in that area of a hydraulic system. The reservoir is in a bad place for me. It is hard to check/add oil if needed, let alone try and manually operate the hydraulic pump. I asked Lippert about a replacement cylinder for a "door side" slide. Gave them all the S/N, VIN, etc. they emailed me back and asked me what color I wanted. Really? You can't see the cylinder for the slideout. It is between the floor and the insulation and underbelly cover. How about black like all the other ones! Anyway, I have talked to 3 different tech support guys there and have received almost 3 different variations of answers. 

I have a question. If I have a solenoid valve that operates the front landing gear simultaneously. They do not operate independently. The supply fluid (2 hoses) go to the cylinder (one each ). The return fluid hose ( one each ) return to the reservoir. The slideout has a separate solenoid, separate hoses, completely separate other than they drain back to one reservoir. How could a leak on a slideout cylinder cause my front landing gear to drop or drift down? I do not get it. Now what am I missing? 



__________________

Bruce & Robin

2013 GMC Sierra 3500HD SLT DRW 4x4 CC

2014 DRV Mobile Suites 38TKSB3 

Full Timers - March 2017

Our Blog at https://rv-revelations.blog/



RV-Dreams Family Member

Status: Offline
Posts: 2074
Date:

Bruce and Robin wrote:

I have a question. If I have a solenoid valve that operates the front landing gear simultaneously. They do not operate independently. The supply fluid (2 hoses) go to the cylinder (one each ). The return fluid hose ( one each ) return to the reservoir. The slideout has a separate solenoid, separate hoses, completely separate other than they drain back to one reservoir. How could a leak on a slideout cylinder cause my front landing gear to drop or drift down? I do not get it. Now what am I missing? 


 Bruce, honestly, I haven't a clue. Way to complicated for me to figure out without a diagram. Everyone has personal preferences but I don't "prefer" the Lippert "Level Up" system.  It simply doesn't have the functionality I prefer.  Meaning, for one thing, one can't run the jacks independently.   That alone is not a good system IMO.  I know it has a purpose, but I still want totally independent operation and I will take responsibility for protecting my frame.  A choice.



__________________

Bill & Linda



RV-Dreams Family Member

Status: Offline
Posts: 1122
Date:

RonC wrote:

The relay click you are hearing should be a contactor sending power to the pump motor. That's a good sign in that all the electrical controls are working correctly up to the contactor.  If the pump isn't turning (you would hear the noise) then the motor is most likely shot. Could be a loose connection, blown fuse, tripped overload or something else, but failed electric motors aren't unusual. Wait a while and see if a thermal overload might have tripped and will reset itself. Failing that, and assuming you know how to use a multimeter ... ensure the ground wire (of the pump motor) is properly connected (it is usually a black heavy wire) and there is continuity with ground, then with the multimeter black lead on ground, put the red lead on the positive side of the pump motor (usually a red colored heavy wire). Have someone activate the "retract" function to try to raise the front landing gear. If the click of the contractor causes the multimeter to go from "0" volts on the motor positive terminal, to go to "12V DC", but the motor does not turn the electrical connection to the pump motor is probably sound ... and the motor has failed internally. The pump can be run manually using a drill motor (most people have a cordless drill). Not sure of the size of the socket pocket on the motor, but running the cordless drill one way will turn the pump in a direction that will extend the gear and reversing the drill motor will cause the pump to run the other way and retract the gear. This should allow you to get everything sucked up and able to travel ... go directly to a shop for repairs. If none of this makes sense, then call a mobile RV Technician.

Sorry to hear of your troubles ... these things ALWAYS happen at inopportune times. Best of luck to you on this.

Ron



-- Edited by RonC on Thursday 8th of June 2017 03:56:02 PM



-- Edited by RonC on Thursday 8th of June 2017 05:52:53 PM


 This procedure is described in the owners manual on page 10 of 12.  Just google Lippert level up owners manual.



__________________

Ron and Janice

 

2016 Ford F350, King Ranch, DRW, 4x4, CC, 6.7 PS Diesel, remote control air lift system

2017 Durango Gold 381REF, Lambright furniture, MCD shades, morRYDE IS, 8K Disc brakes, GY G114  LR H Tires, 27,320 lbs CGVW

FT class of 2016



RV-Dreams Family Member

Status: Offline
Posts: 1122
Date:

Bruce,

I'm no Lippert Expert, so let's get that out of the way. The hydraulic cylinders don't have a "return" line. The two lines serve as either the pressure line or the return line depending on directional function. The cylinders are "powered" both directions (down and up), so each line serves both purposes depending on the direction of travel.

To respond to your question re: slide cylinder leaking causing main landing gear to drift ... there should be no relationship between the two. Something is leaking internally to allow that to happen. The Lippert system is complex in as much as it uses many controls, valves and seals to allow ONE pump and ONE motor to run all those systems (in my system it runs the main landing gear, two pairs of rear leveling jacks and 4 slides). I have the same system and just pray that the hydraulic monsters don't visit me. Honestly, if they did, I would try to get it fixed (within reason), then I would have it removed and replaced by a better system.

Adding a bit more.  The Lippert Level Up system is a great system WHEN IT WORKS.  When "problelms" occur it is difficult to repair due to it's complexity.  I will tell you that the enemy of hydraulic systems is dirt and moisture.  Dirt is abrasive an WILL cause internal wear and resulting leaking (often manifests as "drifting").  Same is true of moisture.  It allows corrosion to occur internally which causes leaks internally as well.  Hydraulic systems need seals riding on near perfect surfaces that allows a good seal.  Corrosion and wear both interfere with that needed sealing.  It is for that reason that fixing it is so hard, the defect could be anywhere and is difficult to isolate.  Replacing all components usually would fix it, but is also very expensive.  Just fully flushing out a contaminated system is very expensive, if done correctly.

More adding ... if there is "evidence" of a leak (damp seals, dripping hydraulic fluid) then the system is contaminated.  If oil can get out, dirt can get in.

-- Edited by RonC on Monday 12th of June 2017 04:38:41 PM



-- Edited by RonC on Monday 12th of June 2017 05:45:22 PM

__________________

Ron and Janice

 

2016 Ford F350, King Ranch, DRW, 4x4, CC, 6.7 PS Diesel, remote control air lift system

2017 Durango Gold 381REF, Lambright furniture, MCD shades, morRYDE IS, 8K Disc brakes, GY G114  LR H Tires, 27,320 lbs CGVW

FT class of 2016



RV-Dreams Family Member

Status: Offline
Posts: 420
Date:

It's been a busy few days.  This may sound ridiculously simple, but the water in our golf cart batteries was low in a few of them.  Our bad for not checking the batteries as often lately.  Steve added water, put in a new 12v 50amp circuit breaker and it seems to work.  We will know for sure tomorrow when we are moving.  He did get the legs to move slightly but that is all he tried as he really want's to wait until tomorrow.  We usually carry spare breakers, but were out and they didn't have them in stock.  Just picked them up.

Thank you for all the help and I'll let you know more tomorrow!



__________________

Debbie & Steve McCormack...and Hurley too!

Our Blog: Down the Road

2013 Montana 3582RL

2013 Dodge 3500HD Laramie Longhorn Dually

Fulltime since June 2014



RV-Dreams Family Member

Status: Offline
Posts: 1122
Date:

DebbieM wrote:

It's been a busy few days.  This may sound ridiculously simple, but the water in our golf cart batteries was low in a few of them.  Our bad for not checking the batteries as often lately.  Steve added water, put in a new 12v 50amp circuit breaker and it seems to work.  We will know for sure tomorrow when we are moving.  He did get the legs to move slightly but that is all he tried as he really want's to wait until tomorrow.  We usually carry spare breakers, but were out and they didn't have them in stock.  Just picked them up.

Thank you for all the help and I'll let you know more tomorrow!


 The new breaker must have been the fix.  In your OP you said you were "still plugged in" so battery maintenance shouldn't have come into play.  Glad it worked out!



__________________

Ron and Janice

 

2016 Ford F350, King Ranch, DRW, 4x4, CC, 6.7 PS Diesel, remote control air lift system

2017 Durango Gold 381REF, Lambright furniture, MCD shades, morRYDE IS, 8K Disc brakes, GY G114  LR H Tires, 27,320 lbs CGVW

FT class of 2016

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.

Tweet this page Post to Digg Post to Del.icio.us